CCNA 1 – Final Exam Answer 2016 100%

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

1. Which communication tool allows real-time collaboration?

• wiki
• e-mail
• weblog
• instant messaging

2. A host is accessing a Web server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.)

• regenerating data signals
• acting as a client or a server
• providing a channel over which messages travel
• applying security settings to control the flow of data
• notifying other devices when errors occur
• serving as the source or destination of the messages

3. A home user is looking for an ISP connection that provides high speed digital transmission over regular phone lines. What ISP connection type should be used?

• DSL
• dial-up
• satellite
• cell modem
• cable modem

4. A company is expanding its business to other countries. All branch offices must remain connected to corporate headquarters at all times. Which network technology is required to support this requirement?

• LAN
• MAN
• WAN
• WLAN

5.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. From which location did this router load the IOS?

• flash memory
• NVRAM?
• RAM
• ROM
• a TFTP server?

6. Which connection provides a secure CLI session with encryption to a Cisco network device?

• a console connection
• an AUX connection
• a Telnet connection
• an SSH connection

7.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. An administrator is trying to configure the switch but receives the error message that is displayed in the exhibit. What is the problem?

• The entire command, configure terminal, must be used.
• The administrator is already in global configuration mode.
• The administrator must first enter privileged EXEC mode before issuing the command.
• The administrator must connect via the console port to access global configuration mode.

8. An administrator uses the Ctrl-Shift-6 key combination on a switch after issuing the ping command. What is the purpose of using these keystrokes?

• to restart the ping process
• to interrupt the ping process
• to exit to a different configuration mode
• to allow the user to complete the command

9. What function does pressing the Tab key have when entering a command in IOS?

• It aborts the current command and returns to configuration mode.
• It exits configuration mode and returns to user EXEC mode.
• It moves the cursor to the beginning of the next line.
• It completes the remainder of a partially typed word in a command.

10.

An administrator wants to change the name of a brand new switch, using the hostname command as shown. What prompt will display after the command is issued??

Refer to the exhibit. An administrator wants to change the name of a brand new switch, using the hostname command as shown. What prompt will display after the command is issued??

• My Switch(config)#?
• Switch(config)#?
• MySwitch(config)#?
• My(config)#?
• Switch#

11.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. A network administrator is configuring access control to switch SW1. If the administrator uses Telnet to connect to the switch, which password is needed to access user EXEC mode?

• letmein
• secretin
• lineconin
• linevtyin

12. After making configuration changes, a network administrator issues a copy running-config startup-config command in a Cisco switch. What is the result of issuing this command?

• The new configuration will be stored in flash memory.
• The new configuration will be loaded if the switch is restarted.
• The current IOS file will be replaced with the newly configured file.
• The configuration changes will be removed and the original configuration will be restored.

13.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. Which action will be successful?

• PC1 can send a ping to 192.168.1.1?.
• PC1 can send a ping to 192.168.1.254?.
• PC2 can send a ping to 192.168.1.1.
• PC2 can send a ping to 192.168.1.254?.

14. Which IPv4 address can be pinged to test the internal TCP/IP operation of a host?

• 0.0.0.0
• 0.0.0.1
• 127.0.0.1
• 192.168.1.1
• 255.255.255.255

15. What three application layer protocols are part of the TCP/IP protocol suite? (Choose three.)

• ARP
• DHCP
• DNS
• FTP
• NAT
• PPP

16. Which two protocols function at the internet layer? (Choose two.)

• ARP
• BOOTP
• ICMP
• IP
• PPP

17. Which publicly available resources describe protocols, processes, and technologies for the Internet but do not give implementation details?

• Request for Comments
• IRTF research papers
• protocol models
• IEEE standards

18. Which address on a PC does not change, even if the PC is moved to a different network?

• IP address
• default gateway address
• MAC address
• logical address

19. What is the protocol that is used to discover a physical address from a known logical address and what message type does it use?

• ARP, multicast
• DNS, unicast
• DNS, broadcast
• ARP, broadcast
• PING, multicast
• PING, broadcast

20. What will happen if the default gateway address is incorrectly configured on a host?

• The host cannot communicate with other hosts in the local network.
• The switch will not forward packets initiated by the host.
• The host will have to use ARP to determine the correct address of the default gateway.
• The host cannot communicate with hosts in other networks.
• A ping from the host to 127.0.0.1 would not be successful.

21. What is an important function of the physical layer of the OSI model?

• It accepts frames from the physical media.
• It encapsulates upper layer data into frames.
• It defines the media access method performed by the hardware interface.
• It encodes frames into electrical, optical, or radio wave signals.

22. Which procedure is used to reduce the effect of crosstalk in copper cables?

• requiring proper grounding connections
• twisting opposing circuit wire pairs together
• wrapping the bundle of wires with metallic shielding
• designing a cable infrastructure to avoid crosstalk interference
• avoiding sharp bends during installation

23. Which two statements describe the characteristics of fiber-optic cabling? (Choose two.)

• Fiber-optic cabling does not conduct electricity.
• Fiber-optic cabling has high signal loss.
• Fiber-optic cabling is primarily used as backbone cabling.
• Multimode fiber-optic cabling carries signals from multiple sending devices.
• Fiber-optic cabling uses LEDs for single-mode cab?les and laser technology for multimode cables.

24. What is contained in the trailer of a data-link frame?

• logical address
• physical address
• data
• error detection

25. What is the auto-MDIX feature on a switch?

• the automatic configuration of an interface for 10/100/1000 Mb/s operation
• the automatic configuration of an interface for a straight-through or a
  crossover Ethernet cable connection
• the automatic configuration of full-duplex operation over a single Ethernet copper or optical cable
• the ability to turn a switch interface on or off accordingly if an active connection is detected

26.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. A ping to PC3 is issued from PC0, PC1, and PC2 in this exact order. Which MAC addresses will be contained in the S1 MAC address table that is associated with the Fa0/1 port?

• just PC0 and PC1 MAC addresses
• just the PC0 MAC address
• PC0, PC1, and PC2 MAC addresses
• just the PC1 MAC address
• just the PC2 MAC address?

27. How does a Layer 3 switch differ from a Layer 2 switch?

• A Layer 3 switch supports VLANs, but a Layer 2 switch does not.
• An IP address can be assigned to a physical port of a Layer 3 switch. However, this is not supported in Layer 2 switches.
• A Layer 3 switch maintains an IP address table instead of a MAC address table.
• A Layer 3 switch learns the MAC addresses that are associated with each of its ports.
• However, a Layer 2 switch does not.

28. What is the purpose of the routing process?

• to encapsulate data that is used to communicate across a network
• to select the paths that are used to direct traffic to destination networks
• to convert a URL name into an IP address
• to provide secure Internet file transfer
• to forward traffic on the basis of MAC addresses

29. Which technology provides a solution to IPv4 address depletion by allowing multiple devices to share one public IP address?

• ARP
• DNS
• NAT
• SMB
• DHCP
• HTTP

30.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. Consider the IP address configuration shown from PC1. What is a description of the default gateway address?

• It is the IP address of the Router1 interface that connects the company to the Internet.
• It is the IP address of the Router1 interface that connects the PC1 LAN to Router1.
• It is the IP address of Switch1 that connects PC1 to other devices on the same LAN.
• It is the IP address of the ISP network device located in the cloud.

31. Which of the following are primary functions of a router? (Choose two.)

• packet switching
• microsegmentation
• domain name resolution
• path selection
• flow control

32. Which two statements correctly describe a router memory type and its contents? (Choose two.)

• ROM is nonvolatile and stores the running IOS.
• FLASH is nonvolatile and contains a limited portion of the IOS?.
• RAM is volatile and stores the running configuration.
• NVRAM is nonvolatile and stores a full version of the IOS.
• ROM is nonvolatile and stores bootup information.

33. In which default order will a router search for startup configuration information?

• NVRAM, RAM, TFTP
• NVRAM, TFTP, setup mode
• setup mode, NVRAM, TFTP
• TFTP, ROM, NVRAM
• flash, ROM, setup mode

34. What happens when part of an Internet VoIP transmission is not delivered to the destination?

• A delivery failure message is sent to the source host.
• The part of the VoIP transmission that was lost is re-sent.
• The entire transmission is re-sent.
• The transmission continues without the missing portion.

35. Which three IP addresses are private ? (Choose three.)

• 10.172.168.1
• 172.32.5.2
• 192.167.10.10
• 172.20.4.4
• 192.168.5.254
• 224.6.6.6

36. How many bits make up the single IPv6 hextet :10CD:?

• 4
• 8
• 16
• 32

37. What is the effect of configuring the ipv6 unicast-routing command on a router?

• to assign the router to the all-nodes multicast group
• to enable the router as an IPv6 router
• to permit only unicast packets on the router
• to prevent the router from joining the all-routers multicast group

38. Which group of IPv6 addresses cannot be allocated as a host source address??

• FEC0::/10?
• FDFF::/7?
• FEBF::/10?
• FF00::/8

39. What is the purpose of ICMP messages?

• to inform routers about network topology changes
• to ensure the delivery of an IP packet
• to provide feedback of IP packet transmissions
• to monitor the process of a domain name to IP address resolution

40.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. A technician has configured a user workstation with the IP address and default subnet masks that are shown. Although the user can access all local LAN resources, the user cannot access any Internet sites by using either FQDN or IP addresses. Based upon the exhibit, what could account for this failure?

• The DNS server addresses are incorrect.
• The default gateway address in incorrect.
• The wrong subnet mask was assigned to the workstation.
• The workstation is not in the same network as the DNS servers.

41. Which subnet would include the address 192.168.1.96 as a usable host address?

• 192.168.1.64/26
• 192.168.1.32/27
• 192.168.1.32/28
• 192.168.1.64/29

42. A network administrator needs to monitor network traffic to and from servers in a data center. Which features of an IP addressing scheme should be applied to these devices?

• random static addresses to improve security
• addresses from different subnets for redundancy
• predictable static IP addresses for easier identification
• dynamic addresses to reduce the probability of duplicate addresses

43.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. Which IP addressing scheme should be changed?

• Site 1
• Site 2
• Site 3
• Site 4

44. Which two notations are useable nibble boundaries when subnetting in IPv6? (Choose two.)

• /62
• /64
• /66
• /68
• /70

45. A host PC has just booted and is attempting to lease an address through DHCP. Which two messages will the client typically broadcast on the network? (Choose two.)

• DHCPDISCOVER
• DHCPOFFER
• DHCPREQUEST
• DHCPACK
• DHCPNACK

46. What is the purpose of the network security accounting function?

• to require users to prove who they are
• to determine which resources a user can access
• to keep track of the actions of a user
• to provide challenge and response questions

47. When applied to a router, which command would help mitigate brute-force password attacks against the router?

• exec-timeout 30
• service password-encryption
• banner motd $Max failed logins = 5$
• login block-for 60 attempts 5 within 60

48. A particular website does not appear to be responding on a Windows 7 computer. What command could the technician use to show any cached DNS entries for this web page?

• ipconfig /all
• arp -a
• ipconfig /displaydns
• nslookup

49.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. The network administrator enters these commands into the R1 router:
R1# copy running-config tftp
Address or name of remote host [ ]?
When the router prompts for an address or remote host name, what IP address should the administrator enter at the prompt?

• 192.168.9.254
• 192.168.10.1
• 192.168.10.2
• 192.168.11.252
• 192.168.11.254

50. Match the IPv6 address to the IPv6 address type. (Not all options are used.)

Match the IPv6 address to the IPv6 address type. (Not all options are used.)

51. What two preconfigured settings that affect security are found on most new wireless routers? (Choose two.)

• broadcast SSID
• MAC filtering enabled
• WEP encryption enabled
• PSK authentication required
• default administrator password

52. Which type of wireless security generates dynamic encryption keys each time a client associates with an AP?

• EAP
• PSK
• WEP
• WPA

53. Fill in the blank.
TFTP    is a best-effort, connectionless application layer protocol that is used to transfer files.

54. Which two components are necessary for a wireless client to be installed on a WLAN? (Choose two.)

• media
• wireless NIC
• custom adapter
• crossover cable
• wireless bridge
• wireless client software

55. Consider the following range of addresses:
2001:0DB8:BC15:00A0:0000::
2001:0DB8:BC15:00A1:0000::
2001:0DB8:BC15:00A2:0000::
…
2001:0DB8:BC15:00AF:0000::
The prefix-length for the range of addresses is       /60   .

56. Match the phases to their correct stage in the router bootup process. (Not all options are used.)

Match the phases to their correct stage in the router bootup process. (Not all options are used.)

57. A host is accessing an FTP server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.)

• regenerating data signals
• acting as a client or a server
• providing a channel over which messages travel
• applying security settings to control the flow of data
• notifying other devices when errors occur
• serving as the source or destination of the messages

58. When is a dial-up connection used to connect to an ISP?

• when a cellular telephone provides the service
• when a high-speed connection is provided over a cable TV network
• when a satellite dish is used
• when a regular telephone line is used

59. On a school network, students are surfing the web, searching the library database, and attending an audio conference with their sister school in Japan. If network traffic is prioritized with QoS, how will the traffic be classified from highest priority to lowest priority?

• audio conference, database, HTTP
• database, HTTP, audio conference
• audio conference, HTTP, database
• database, audio conference, HTTP

60. During normal operation, from which location do most Cisco routers run the IOS?

• RAM
• flash
• NVRAM
• disk drive

61. Which connection provides a secure CLI session with encryption to a Cisco switch?

• a console connection
• an AUX connection
• a Telnet connection
• an SSH connection

62. Which keys act as a hot key combination that is used to interrupt an IOS process?

• Ctrl-Shift-X
• Ctrl-Shift-6
• Ctrl-Z
• Ctrl-C

63.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. An administrator wants to change the name of a brand new switch, using the hostname command as shown. What prompt will display after the command is issued??

• HR Switch(config)#?
• Switch(config)#?
• HRSwitch(config)#?
• HR(config)#?
• Switch#

64. After making configuration changes on a Cisco switch, a network administrator issues a copy running-config startup-config command. What is the result of issuing this command?

• The new configuration will be stored in flash memory.
• The new configuration will be loaded if the switch is restarted.
• The current IOS file will be replaced with the newly configured file.
• The configuration changes will be removed and the original configuration will be restored.

65. On which switch interface would an administrator configure an IP address so that the switch can be managed remotely?

• FastEthernet0/1
• VLAN 1
• vty 0
• console 0

66. A technician uses the ping 127.0.0.1 command. What is the technician testing?

• the TCP/IP stack on a network host
• connectivity between two adjacent Cisco devices
• connectivity between a PC and the default gateway
• connectivity between two PCs on the same network
• physical connectivity of a particular PC and the network

67. What is the correct order for PDU encapsulation?

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

68. Which device should be used for enabling a host to communicate with another host on a different network?

• switch
• hub
• router
• host

69. A network technician is measuring the transfer of bits across the company backbone for a mission critical application. The technician notices that the network throughput appears lower than the bandwidth expected. Which three factors could influence the differences in throughput? (Choose three.)

• the amount of traffic that is currently crossing the network
• the sophistication of the encapsulation method applied to the data
• the type of traffic that is crossing the network
• the latency that is created by the number of network devices that the data is crossing
• the bandwidth of the WAN connection to the Internet
• the reliability of the gigabit Ethernet infrastructure of the backbone

70. Which characteristics describe fiber optic cable? (Choose two.)

• It is not affected by EMI or RFI.
• Each pair of cables is wrapped in metallic foil.
• It combines the technique of cancellation, shielding and twisting to protect data.
• It has a maximum speed of 100 Mbps.
• It is the most expensive type of LAN cabling

71. What are two features of a physical, star network topology? (Choose two.)

• It is straightforward to troubleshoot.
• End devices are connected together by a bus.
• It is easy to add and remove end devices.
• All end devices are connected in a chain to each other.
• Each end system is connected to its respective neighbor.

72. A frame is transmitted from one networking device to another. Why does the receiving device check the FCS field in the frame?

• to determine the physical address of the sending device
• to verify the network layer protocol information
• to compare the interface media type between the sending and receiving ends
• to check the frame for possible transmission errors
• to verify that the frame destination matches the MAC address of the receiving device

73. What will a Layer 2 switch do when the destination MAC address of a received frame is not in the MAC table?

• It initiates an ARP request.
• It broadcasts the frame out of all ports on the switch.
• It notifies the sending host that the frame cannot be delivered.
• It forwards the frame out of all ports except for the port at which the frame was received.

74. Which switching method has the lowest level of latency?

• cut-through
• store-and-forward
• fragment-free
• fast-forward

75. Which parameter does the router use to choose the path to the destination when there are multiple routes available?

• the lower metric value that is associated with the destination network
• the lower gateway IP address to get to the destination network
• the higher metric value that is associated with the destination network
• the higher gateway IP address to get to the destination network

76. Which two statements describe the functions or characteristics of ROM in a router? (Choose two.)

• stores routing tables
• allows software to be updated without replacing pluggable chips on the motherboard
• maintains instructions for POST diagnostics
• holds ARP cache
• stores bootstrap program

77. Which statement describes a characteristic of the Cisco router management ports?

• A console port is used for remote management of the router.
• A console port is not used for packet forwarding.
• Serial and DSL interfaces are types of management ports.
• Each Cisco router has a LED indicator to provide information about the status of the management ports.

78. What happens when part of an Internet radio transmission is not delivered to the destination?

• A delivery failure message is sent to the source host.
• The part of the radio transmission that was lost is re-sent.
• The entire transmission is re-sent.
• The transmission continues without the missing portion.

79. What is the dotted decimal representation of the IPv4 address 11001011.00000000.01110001.11010011?

• 192.0.2.199
• 198.51.100.201
• 203.0.113.211
• 209.165.201.223

80. Which three IP addresses are private ? (Choose three.)

• 10.20.30.1
• 172.32.5.2
• 192.167.10.10
• 172.30.5.3
• 192.168.5.5
• 224.6.6.6

81. What types of addresses make up the majority of addresses within the /8 block IPv4 bit space?

• private addresses
• public addresses
• multicast addresses
• experimental addresses

82.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. What is the maximum TTL value that is used to reach the destination www.cisco.com??

• 11
• 12
• 13
• 14

83. A company has a network address of 192.168.1.64 with a subnet mask of 255.255.255.192. The company wants to create two subnetworks that would contain 10 hosts and 18 hosts respectively. Which two networks would achieve that? (Choose two.)

• 192.168.1.16/28
• 192.168.1.64/27
• 192.168.1.128/27
• 192.168.1.96/28
• 192.168.1.192/28

84. In a network that uses IPv4, what prefix would best fit a subnet containing 100 hosts?

• /23
• /24
• /25
• /26

85. Which protocol supports rapid delivery of streaming media?

• Transmission Control Protocol
• Real-Time Transport Protocol
• Secure File Transfer Protocol
• Video over Internet Protocol

86. Why would a network administrator use the tracert utility?

• to determine the active TCP connections on a PC
• to check information about a DNS name in the DNS server
• to identify where a packet was lost or delayed on a network
• to display the IP address, default gateway, and DNS server address for a PC

87.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. What is the significance of the asterisk in the exhibited output?

• The asterisk shows which file system was used to boot the system.
• The asterisk designates which file system is the default file system.
• An asterisk indicates that the file system is bootable.
• An asterisk designates that the file system has at least one file that uses that file system.

88. Which WLAN security protocol generates a new dynamic key each time a client establishes a connection with the AP?

• EAP
• PSK
• WEP
• WPA

89. Fill in the blank.
Point-to-point communications where both devices can transmit and receive on the medium at the same time are known as      full-duplex .

90. Match each characteristic to the appropriate email protocol. (Not all options are used.)

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

91. A host is accessing a Telnet server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.)

• regenerating data signals
• acting as a client or a server
• providing a channel over which messages travel
• applying security settings to control the flow of data
• notifying other devices when errors occur
• serving as the source or destination of the messages

92.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. Which area would most likely be an extranet for the company network that is shown?

• area A
• area B
• area C
• area D

93. What is the purpose of having a converged network?

• to provide high speed connectivity to all end devices
• to make sure that all types of data packets will be treated equally
• to achieve fault tolerance and high availability of data network infrastructure devices
• to reduce the cost of deploying and maintaining the communication infrastructure

94. Three office workers are using the corporate network. The first employee uses a web browser to view a company web page in order to read some announcements. The second employee accesses the corporate database to perform some financial transactions. The third employee participates in an important live audio conference with other office workers in branch offices. If QoS is implemented on this network, what will be the priorities from highest to lowest of the different data types?

• audio conference, financial transactions, web page
• financial transactions, web page, audio conference
• audio conference, web page, financial transactions
• financial transactions, audio conference, web page

95. During normal operation, from which location do most Cisco switches and routers run the IOS?

• RAM
• flash
• NVRAM
• disk drive

96. A network administrator is making changes to the configuration of a router. After making the changes and verifying the results, the administrator issues the copy running-config startup-config command. What will happen after this command executes?

• The configuration will be copied to flash.
• The configuration will load when the router is restarted.
• The new configuration file will replace the IOS file.
• The changes will be lost when the router restarts.

97. What information does the loopback test provide?

• The TCP/IP stack on the device is working correctly.
• The device has end-to-end connectivity.
• DHCP is working correctly.
• The Ethernet cable is working correctly.
• The device has the correct IP address on the network.

98. What is a characteristic of the LLC sublayer?

• It provides the logical addressing required that identifies the device.
• It provides delimitation of data according to the physical signaling requirements of the medium.
• It places information in the frame allowing multiple Layer 3 protocols to use the same network interface and media.
• It defines software processes that provide services to the physical layer.

99. What method is used to manage contention-based access on a wireless network?

• CSMA/CD
• priority ordering
• CSMA/CA
• token passing

100. What happens when a switch receives a frame and the calculated CRC value is different than the value that is in the FCS field?

• The switch places the new CRC value in the FCS field and forwards the frame.
• The switch notifies the source of the bad frame.
• The switch drops the frame.
• The switch floods the frame to all ports except the port through which the frame arrived to notify the hosts of the error.

101. Which destination address is used in an ARP request frame?

• 0.0.0.0
• 255.255.255.255
• FFFF.FFFF.FFFF
• 127.0.0.1
• 01-00-5E-00-AA-23

102. What is the auto-MDIX feature on a switch?

• the automatic configuration of an interface for 10/100/1000 Mb/s operation
• the automatic configuration of an interface for a straight-through or a crossover Ethernet cable connection
• the automatic configuration of full-duplex operation over a single Ethernet copper or optical cable
• the ability to turn a switch interface on or off accordingly if an active connection is detected

103. Which frame forwarding method receives the entire frame and performs a CRC check to detect errors before forwarding the frame?

• cut-through switching
• store-and-forward switching
• fragment-free switching
• fast-forward switching

104. What are the two main components of Cisco Express Forwarding (CEF)? (Choose two.)

• adjacency tables
• MAC-address tables
• routing tables
• ARP tables
• forwarding information base (FIB)

105. Which statement describes the sequence of processes executed by a router when it receives a packet from a host to be delivered to a host on another network?

• It receives the packet and forwards it directly to the destination host.
• It de-encapsulates the packet, selects the appropriate path, and encapsulates the packet to forward it toward the destination host.
• It de-encapsulates the packet and forwards it toward the destination host.
• It selects the path and forwards it toward the destination host.

106. Which technology provides a solution to IPv4 address depletion by allowing multiple devices to share one public IP address?

• ARP
• DNS
• NAT
• SMB
• DHCP
• HTTP

107.

CCNA 1 – Introduction to Network Final Exam Answer 2016 100%

Refer to the exhibit. Router R1 has two interfaces that were configured with correct IP addresses and subnet masks. Why does the show ip route command output not display any information about the directly connected networks??

• The directly connected networks have to be created manually to be displayed in the routing table.
• The routing table will only display information about these networks when the router receives a packet.
• The no shutdown command was not issued on these interfaces.
• The gateway of last resort was not configured.

108. What happens when part of an Internet television transmission is not delivered to the destination?

• A delivery failure message is sent to the source host.
• The part of the television transmission that was lost is re-sent.
• The entire transmission is re-sent.
• The transmission continues without the missing portion.

109. Which three statements characterize the transport layer protocols? (Choose three.)

• TCP and UDP port numbers are used by application layer protocols.
• TCP uses port numbers to provide reliable transportation of IP packets.
• UDP uses windowing and acknowledgments for reliable transfer of data.
• TCP uses windowing and sequencing to provide reliable transfer of data.
• TCP is a connection-oriented protocol. UDP is a connectionless protocol.

110. A user opens three browsers on the same PC to access www.cisco.com to search for certification course information. The Cisco web server sends a datagram as a reply to the request from one of the web browsers. Which information is used by the TCP/IP protocol stack in the PC to identify the destination web browser?

• the destination IP address
• the destination port number
• the source IP address
• the source port number

111. Which statement is true regarding the UDP client process during a session with a server?

• Datagrams that arrive in a different order than that in which they were sent are not placed in order.
• A session must be established before datagrams can be exchanged.
• A three-way handshake takes place before the transmission of data begins.
• Application servers have to use port numbers above 1024 in order to be UDP capable.

112. Which two components are configured via software in order for a PC to participate in a network environment? (Choose two.)

• MAC address
• IP address
• kernel
• shell
• subnet mask

113. What are three characteristics of multicast transmission? (Choose three.)

• The source address of a multicast transmission is in the range of 224.0.0.0 to 224.0.0.255.
• A single packet can be sent to a group of hosts.
• Multicast transmission can be used by routers to exchange routing information.
• Routers will not forward multicast addresses in the range of 224.0.0.0 to 224.0.0.255.
• Computers use multicast transmission to request IPv4 addresses.
• Multicast messages map lower layer addresses to upper layer addresses.

114. Which two reasons generally make DHCP the preferred method of assigning IP addresses to hosts on large networks? (Choose two.)

• It eliminates most address configuration errors.
• It ensures that addresses are only applied to devices that require a permanent address.
• It guarantees that every device that needs an address will get one.
• It provides an address only to devices that are authorized to be connected to the network.
• It reduces the burden on network support staff.

115. What is the subnet address for the address 2001:DB8:BC15:A:12AB::1/64?

• 2001:DB8:BC15::0
• 2001:DB8:BC15:A::0
• 2001:DB8:BC15:A:1::1
• 2001:DB8:BC15:A:12::0

116. Which two tasks are functions of the presentation layer? (Choose two.)

• compression
• addressing
• encryption
• session control
• authentication

117. What is the purpose of the network security authentication function?

• to require users to prove who they are
• to determine which resources a user can access
• to keep track of the actions of a user
• to provide challenge and response questions

118. Which type of wireless security makes use of dynamic encryption keys each time a client associates with an AP?

• EAP
• PSK
• WEP
• WPA

119. Fill in the blank.
During data communications, a host may need to send a single message to a specific group of destination hosts simultaneously. This message is in the form of a   Multicast    message.

120. Match the description with the associated IOS mode. (Not all options are used.)

Match the description with the associated IOS mode. (Not all options are used.)

Share :

Tweet

✚

Related Post